Download New Updated (July) Cisco 352-001 Actual Test 31-40

Ensurepass

QUESTION 31

Refer to the exhibit. In this design, which technology would provide for the best use of resources to provide end-to-end Layer 2 connectivity?

 

clip_image002

 

A.

MSTP

B.

PAgP

C.

Multichassis EtherChannel

D.

LACP

 

Correct Answer: C

 

 

QUESTION 32

When creating a network design that routes an IGP over L2VPNs, with which device does the remote CE router form an IGP adjacency?

 

A.

the hub site PE router

B.

the hub site CE router

C.

the directly connected PE router

D.

The IGP will not establish adjacency over the MPLS network.

 

Correct Answer: B

 

 

QUESTION 33

When designing a network, which two security features should be added to the design to protect hosts from potential IPv6 neighbor discovery denial of service attacks at the access layer? (Choose two.)

 

A.

SEND

B.

RA Guard

C.

IKEv2

D.

IPsec

E.

DMVPNv6

 

Correct Answer: AB

 

 

QUESTION 34

Network designers plan to interconnect two geographically separated data centers using an Ethernet-over-MPLS pseudowire. Within that design, the link between the sites is stable, there are no apparent loops in the topology, and the root bridges for the respective VLANs are stable and unchanging. What additional aspect of the design should be adjusted to mitigate the chance of connectivity issues to the peer data center when the connection takes place?

 

A.

Enable 802.1d on one data center, and 802.1w on the other.

B.

Ensure that the spanning tree diam

eter for one or more VLANs is not too large.

C.

Enable UDLD on the link between the data centers.

D.

Enable root guard on the link between the data centers.

 

Correct Answer: B

 

 

QUESTION 35

A service provider has a Resilient Ethernet Protocol ring running as a metro backbone between its locations in one city. A customer wants to connect one site with one box redundant to theResilient Ethernet Protocol ring at two different service provider locations. How can this be done without producing any Layer 2 loops within the network design?

 

A.

Spanning tree at the service provider side only must be enabled.

B.

Spanning tree at the customer side only must be enabled.

C.

Flex Links at the service provider side only must be enabled.

D.

Flex Links at the customer side only must be enabled.

E.

EtherChannel at the service provider side and the customer side must be enabled.

F.

Spanning tree at the service provider side and the customer side must be enabled.

G.

Flex Links at the service provider side and the customer side must be enabled.

 

Correct Answer: D

 

 

QUESTION 36

What are two design advantages to using virtual port channel? (Choose two.)

 

A.

enhanced system availability through multiple systems

B.

reduced Spanning Tree Protocol convergence time

C.

loop management without use of Spanning Tree Protocol

D.

ability to use Spanning Tree Protocol blocked ports to forward traffic

E.

enhanced ability to recover from Spanning Tree Protocol changes

 

Correct Answer: AC

 

 

QUESTION 37

When designing a large full mesh network running OSPF, how would you reduce LSA repetition?

 

A.

Elect a DR and BDR.

B.

Use access control lists to control outbound advertisements.

C.

Choose one or two routers to re-flood LSA information.

D.

Put each of the point-to-point links in your full mesh networking into a separate area.

 

Correct Answer: C

 

 

QUESTION 38

Which two mechanisms ensure that a network design provides fast path failure detection? (Choose two.)

 

A.

BFD

B.

fast hello packets

C.

UDLD

D.

IP Cisco Express Forwarding

 

Correct Answer: AB

 

 

QUESTION 39

Company X will be integrating an IPv6 application into their network and wants to develop a test environment to evaluate application performance across the network. This application will require both unicast and multicast communications. The company can do this implementation only in certain areas of its existing IPv4-only network, but wants all areas to communicate with each other. When developing the design to provide connectivity between these testing locations, what tunneling technology would work in this scenario?

 

A.

ISATAP

B.

6to4

C.

DMVPN

D.

6vPE

E.

6PE

 

Correct Answer: C

 

 

QUESTION 40

What are two benefits of following a structured hierarchical and modular design? (Choose two.)

 

A.

Each component can be designed independently for its role.

B.

Each component can be managed independently based on its role.

C.

Each component can be funded by different organizations based on its role.

D.

Each component can support multiple roles based on the requirements.

E.

Each component can provide redundancy for applications and services.

Correct Answer: AB

 

Free VCE & PDF File for Cisco 352-001 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …