[Free] Download New Updated (April 2016) Cisco 350-080 Actual Tests 281-290

Ensurepass

QUESTION 281

Refer to the exhibit. What is the purpose of this command on the Cisco Nexus 7000 switch?

 

clip_image002

 

A.

The command enables conversational learning on FabricPath VLANs 1 through 10 for the F Series module.

B.

The command enables the FabricPath protocol on VLANs 1 through 10.

C.

There is no need for this command because conversational learning is enabled by default for all VLANs.

D.

The command enables conversational learning on a classic Ethernet VLAN for the F Series module.

 

Correct Answer: D

 

 

QUESTION 282

Refer to the exhibit. Which three statements describe the use of the vPC peer link in this topology? (Choose three.)

 

clip_image004

 

A.

The peer link is used for synchronizing MAC addresses between SW1 and SW2.

B.

The peer link is used for control plane traffic only.

C.

The peer link provides necessary transport for multicast traffic.

D.

The peer link is used for the communication of orphaned ports.

E.

The peer link does not prevents the loops in the topology.

F.

The peer link always consists of two 10GB ports in a port-channel.

 

Correct Answer: ACD

 

 

QUESTION 283

What is the default vPC peer-keepalive timeout on the Cisco Nexus 7000 Series switch?

 

A.

5 seconds

B.

256 milliseconds

C.

500 milliseconds

D.

1 second

 

Correct Answer: D

 

 

QUESTION 284

On the Cisco Nexus 7000 switch, ACL capture sessions are supported on which two modules? (Choose two.)

 

A.

M1 modules

B.

M2 modules

C.

F1 modules

D.

F2 modules

E.

M3 modules

 

Correct Answer: AB

 

 

QUESTION 285

Which three configurations for ACL capture are valid? (Choose three.)

 

A.

on a VLAN interface

B.

in the ingress direction on all interfaces

C.

in the ingress direction only on the M2 module

D.

in the egress direction on all interfaces

E.

in the egress direction on all Layer 3 interfaces

F.

in the ingress direction only on M1 module

 

Correct Answer: ABE

 

 

 

 

 

 

 

 

 

QUESTION 286

Refer to the exhibit. A new Nexus device, Router-B, was recently added to the network. The engineer wants to make Router-B the designated IGMP querier for this network. Which two configurations should be applied to the devices on the network to accomplish this goal? (Choose two.)

 

clip_image006

 

A.

Router-B(config)# interface Ethernet1/1

Router-B(config-if)# ip address 10.1.1.251 255.255.255.0

B.

Router-B(config)# interface Ethernet1/1

Router-B(config-if)# ip address 10.1.1.249 255.255.255.0

Router-B(config)# feature igmp

C.

Router-B(config)# interface Ethernet1/1

Router-B(config-if)# ip igmp version 2

Router-B(config)# feature igmp

D.

Router-B(config)# interface Ethernet1/1

Router-B(config-if)# ip igmp querier

Router-B(config)# feature pim

E.

Router-B(config)# interface Ethernet1/1

Router-B(config-if)# ip pim sparse-mode

 

Correct Answer: BE

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 287

Refer to the exhibit. The customer is trying to configure a rendezvous point, but for some reason it is failing. Which configuration should be applied on both Nexus devices to configure the rendezvous point?

 

clip_image007

 

A.

RT-2(config)#ip pim send-rp-discovery loopback10

RT-2(config)#interface lo0

B.

RT-2(config-if)#ip pim-sparse

RT-2(config)#ip pim send-rp-announce lo10 group-list 239.0.0.0/24

RT-2(config)#interface lo0

RT-2(config-if)#ip pim-sparse

C.

RT-2(config)#ip pim send-rp-discovery loopback10

RT-2(config)#interface lo0

RT-2(config-if)#ip pim-sparse

D.

RT-1(config)#interface Vlan106

E.

RT-1(config-if)#no ip pim border

RT-2(config)# ip pim send-rp-announce lo10 group-list 239.0.0.0/24

RT-2(config)#interface lo0

RT-2(config-if)#ip pim-sparse

F.

RT-1(config)#interface Vlan106

G.

RT-1(config-if)#no ip pim border

RT-2(config)# ip pim send-rp-discovery loopback10

H.

RT-1(config)#interface Vlan106

RT-1(config-if)#no ip pim border

 

Correct Answer: C

QUESTION 288

Which of the following is a feature of Fabric Extender?

 

A.

The Fabric Extender provides two user queues for its QoS support, one for all no-drop classes and one for all drop classes.

B.

The class-all-flood and class-ip-multicast class maps are used on the Fabric Extender.

C.

The Fabric Extender inherits the CoS configured on the upstream switch.

D.

For a Cisco Nexus 2248PQ 10GE Fabric Extender, all fabric interfaces can be bundled into a single fabric port channel.

 

Correct Answer: A

 

 

QUESTION 289

You have a customer with an MDS fabric that is experiencing a performance problem. You suspect that the problem is due to a BB credit starvation issue with a host HBA. The customer has both a DS-PAA-2 and a Fibre Channel Analyzer on location. You want to collect a trace and look at the R_RDY flows between the MDS and the host. Which of the following actions is the best way to start troubleshooting this problem?

 

A.

Collect a Fibre Channel Analyzer local brief trace on the MDS and look for missing R_RDYs.

B.

Collect a Fibre Channel Analyzer local trace with full detail on the MDS, because the detail is needed to examine the R_RDY flow.

C.

Use the DS-PAA-2 and the MDS span feature to capture a trace and examine the R_RDY flow between the host and MDS.

D.

Use the Finisar and the MDS span feature to capture a trace because the DS-PAA-2 cannot decode R_RDYs.

E.

Break the physical connection between the host and MDS and insert the Fibre Channel Analyzer inline.

 

Correct Answer: E

 

 

QUESTION 290

Basic zoning changes are accomplished through the use of four SW_ILS frames. Which option identifies these frames in the correct order?

 

A.

RCA, UFC, SFC, ACA

B.

ACA, RCA, SFC, UFC

C.

SFC, UFC, ACA, RCA

D.

ACA, SFC, UFC, RCA

E.

UFC, SFC, RCA, ACA

 

Correct Answer: D

 

Free VCE & PDF File for Cisco 350-080 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …