[Free] Download New Updated (December) Cisco 200-355 Exam Questions 221-230

Ensurepass

QUESTION 221

Which CLI command is used on a Cisco WLC to troubleshoot mobility, rogue detection, and load-balancing events?

 

A.

debug dot11

B.

debug capwap all

C.

show dot11 details

D.

show capwap details

 

Correct Answer: A

 

 

QUESTION 222

clip_image002

clip_image004

clip_image006

clip_image008

clip_image010

clip_image012

clip_image014

clip_image016

 

Old 2.4-GHz wireless laptops are unable to connect. What is the most likely cause of this problem?

 

A.

WLAN > General properties are incorrectly configured.

B.

WLAN > QoS properties are incorrectly configured.

C.

WLAN > Security properties are incorrectly configured.

D.

WLAN > Advanced properties are incorrectly configured.

E.

Wireless > AP > 802.11 b/g/n AP is incorrectly configured.

F.

Wireless > AP > 802.11 b/g/n > Network is incorrectly configured.

 

Correct Answer: F

 

 

 

 

 

QUESTION 223

clip_image018

clip_image020

clip_image022

clip_image024

 

What APTx Power Level Assignment would be required to increase power by 3 dBm on 2.4GHz radio?

 

A.

1

B.

2

C.

3

D.

4

E.

5

F.

6

G.

7

H.

8

 

Correct Answer: D

 

 

QUESTION 224

Which type of management tasks can be completed on a Cisco WLC remotely from a wireless client?

 

A.

All management and configuration tasks can be performed from a wireless client except for using debug commands.

B.

In the default configuration, no management or configuration is possible through the GUI or CLI on the Cisco WLC.

C.

The default configuration of the Cisco WLC allows only CLI access and then only the use of show commands, so no configuration is possible.

D.

All management and configuration tasks, except uploads from and downloads to the Cisco WLC, are permitted.

 

Correct Answer: B

 

 

QUESTION 225

Which three WLC debug commands are appropriate to troubleshoot a wireless client that is associated to an AP? (Choose three.)

 

A.

debug capwap

B.

debug mac addr

C.

debug dot11

D.

debug dhcp

E.

debug ap

F.

debug dtls

 

Correct Answer: BCD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 226

clip_image026

clip_image028

clip_image029

clip_image031

clip_image033

clip_image035

clip_image037

clip_image039

 

Which change can correct inband access to the WLC?

 

A.

change the switch FastEthernetO/1 duplex setting

B.

change the switch FastEthernetO/1 speed setting

C.

enable the switch FastEthernetO/1 spanning-tree port-fast trunk

D.

change the switch FastEthernetO/1 trunk encapsulation

E.

change the WLC management interface to use DHCP

F.

change the WLC management interface VLAN

G.

change the WLC configuration of NTP

H.

browse to WLC via http://10.10.10.10

Correct Answer: D

 

 

QUESTION 227

Which description best describes upfade in a multipath environment?

 

A.

In this situation, multiple signal paths are not sent at exactly the same time. The receiver receives a positive crest on the primary signal and a negative crest on the secondary signal.

B.

In this situation, the multiple signal paths are distorted and difficult to understand.

C.

In this situation, the multiple signal paths are weaker than they should be because the signals are out of phase with each other.

D.

In this situation, the signal is stronger than it should be because multiple signal paths are received twice at exactly the same time, which results in the multiple signals being in- phase.

 

Correct Answer: D

 

 

QUESTION 228

When using DHCP option 43, the discovery option supports vendor specific identifiers in order to obtain what IP address?

 

A.

core router’s gateway

B.

closest distribution switch

C.

local WLAN controller

D.

local Radius Server

 

Correct Answer: C

 

 

QUESTION 229

What three characteristics are components of mobility anchoring? (Choose three.)

 

A.

enabled as a global setting

B.

enabled on a per WLAN basis

C.

restricts clients to a specific subnet

D.

client traffic is tunneled to predefined WLC(s)

E.

only one mobility anchor is allowed per WLAN

F.

acts as master controller for a mobility group

 

Correct Answer: BCD

 

 

QUESTION 230

A customer mounted three new APs in a small business. After configuring the IP address, users still could not access the web through the new access points. What two configurations are needed to fix this? (Choose two.)

 

A.

Security parameters

B.

Gateway address

C.

Service Set ID

D.

Antenna option

E.

EAP Authentication

F.

Unique AP Name

Correct Answer: BC

 

Free VCE & PDF File for Cisco 200-355 Exam Questions

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …