New Updated Cisco CCNA R&S 200-120 Real Exam Download 301-310

Ensurepass

QUESTION 301

Which protocol can cause overload on a CPU of a managed device?

 

A.      Netflow

B.      WCCP

C.      IP SLA

D.      SNMP

 

Correct Answer: D

 

 

QUESTION 302

What are the three things that the Netflow uses to consider the traffic to be in a same flow?

 

A.      IP address

B.      Interface name

C.      Port numbers

D.      L3 protocol type

E.       MAC address

 

Correct Answer: ACD

 

 

QUESTION 303

What is the alert message generated by SNMP agents called?

 

A.      TRAP

B.      INFORM

C.      GET

D.      SET

 

Correct Answer: AB

 

 

QUESTION 304

Which three features are added in SNMPv3 over SNMPv2?

 

A.      Message Integrity

B.      Compression

C.      Authentication

D.      Encryption

E.       Error Detection

 

Correct Answer: ACD

 

 

QUESTION 305

In a GLBP network, who is responsible for the arp request?

 

A.      AVF

B.      AVG

C.      Active Router

D.      Standby Router

 

Correct Answer: B

 

 

QUESTION 306

Which one of these is a valid HSRP Virtual Mac Address?

 

A.      0000.0C07.AC01

B.      0000.5E00.0110

C.      0007.B400.1203

D.      0000.C007.0201

 

Correct Answer: A

 

 

QUESTION 307

What levels will be trapped if the administrator executes the command (Choose four.)

 

router(cfg)#logging trap 4

 

A.      Emergency

B.      Notice

C.      Alert

D.      Error

E.       Warning

 

Correct Answer: ACDE

 

 

QUESTION 308

What are the three things that netflow uses to consider the traffic to be in a same flow?

 

A.      IP address

B.      Interface name

C.      Port numbers

D.      L3 protocol type

 

Correct Answer: ACD

 

 

QUESTION 309

Which is true about OSPF router-id? (Choose two.)

 

A.      It is used for type 1 router LSA

B.      Highest IP address of the loopback is used

C.      router-id needs to be matched on ospf neighbors

D.      router-id is 16 bit

 

Correct Answer: AB

 

 

QUESTION 310

Lab-EIGRP

After adding BLD-102 router, no routing updates are being exchanged between BLD-102 and the new location. All other inter connectivity and Internet access for the existing locations of the company are working properly.

The task is to identify the fault(s) and correct the router configuration to provide full connectivity between the routers.

Access to the router CLI can be gained by clicking on the appropriate host. All passwords on all routers are cisco.

IP addresses are listed in the chart below.

 

 

Correct Answer:

EIGRP Lab is a troubleshooting problem, use the command show run to find the topology diagram four EIGRP router configuration errors and corrections, so that the network is the all-pass completion of the experiment. There are two types of errors: 1. AS number is wrong; 2.Segment declaration is wrong. Be remember after finishing each segment ping about whether the pass. Finally remember Copy running-config Startup-config.

 

 

BLD-102>enable (Need to enter the password cisco)

BLD-102#configure terminal

 

 

AS number is wrong, you need to delete the entire eigrp, re-declaration.

 

BLD-102(config)#no router eigrp 22

BLD-102(config)#router eigrp 122

BLD-102(config-router)#network 192.168.22.0

BLD-102(config-router)#network 192.168.84.0

BLD-102(config-router)#no auto-summary

BLD-102(config-router)#end

BLD-102#copy running-config startup-config

 

Campus>enable (Need to enter the password cisco)

 

 

Campus#configure terminal

Campus(config)#router eigrp 122

Campus(config-router)#network 192.168.22.0

Campus(config-router)#no network 192.168.29.0

Campus(config-router)#end

Campus#copy running-config startup-config

 

This router has a passive-interface S1/0 configuration, there is no error, without treatment.

 

Download Latest Complete Collection of CCNA R&S 200-120 Real Exam ,help you to pass exam 100%.

Ensurepass Cisco Certifications Exam Questions and Answers
Ensurepass CCNA R&S Exams Questions and Answers

Leave a Reply