New Updated Cisco CCNP 642-902 Real Exam Download 151-160

Ensurepass

QUESTION 151

Refer to the exhibit. Based on the command output, what is one reason why no routes from the OSPF neighbor 192.168.0.5 are installed in the IP routing table?

 

clip_image001

 

A.       R3 will only install routes from the neighbor with the lowest priority (Pri). If routes have the same priority, routes from the neighbor with the lowest IP address are used.

B.       R3 did not receive any LSAs from 192.168.0.5.

C.       Routes from backup designated routers are never installed in the IP routing table.

D.       192.168.0.5 is a redundant link to 192.168.0.4, and load balancing is not enabled.

 

Correct Answer: B

 

 

QUESTION 152

Refer to the exhibit. What additional commands should be used to configure OSPF area 5 as a Totally Stubby area?

 

clip_image002

 

A.  area 0 stub on routers R4 and R5

B.  area 5 stub on routers R4 and R5

C.  area 5 stub no-summary on routers R4 and R5

D.  area 0 stub no-summary on router R4 and area 5 stub no-summary on router R5

E.  area 5 stub no-summary on router R4 and area 5 stub on router R5

 

Correct Answer: E

 

 

QUESTION 153

Refer to the partial configurations in the exhibit. What address is utilized for DR and BDR identification on Router1?

 

clip_image003

 

A.       the configured router-id address

B.       an arbitrarily generated internal address

C.       the sequential 1/1 address

D.      the sequential 2/0 address

 

Correct Answer: A

 

 

QUESTION 154

You are developing a verification plan for an upcoming OSPF implementation. Part of this plan is to verify the status of type 3 LSAs within the network. Which routers should you verify first to ensure that the configurations are correct for generating type 3 LSAs?

 

A.       Internal routers within the backbone area (area 0)

B.       Internal routers within the NSSAs

C.       Internal routers within the stubby areas

D.      ASBRs

E.       ABRs

F.        DRs and BDRs

 

Correct Answer: E

 

 

QUESTION 155

Refer to the exhibit. Based on this command output, what can we conclude about R3?

 

clip_image004

 

A.       R3 is an ABR.

B.       R3 is not connected to the backbone.

C.       R3 has four neighbors.

D.      R3 is the DR for area 2.

 

Correct Answer: A

 

 

QUESTION 156

Refer to the exhibit. A new TAC engineer comes to you for advice. The engineer wants to configure RIPv2- OSPF two-way redistribution while avoiding routing loops. Which two additions to the router B1 configuration should the engineer make? (Choose two.)

clip_image005

 

A.  access-list 40 deny 172.16.1.0 0.0.0.255

    access-list 40 permit any

    router rip

    redistribute ospf 100 metric 5

    distribute-list 40 out ospf 100

 

B.  ip prefix-list rip_routes permit 172.16.1.16/25 ge 26 le 28 route-map redis-ospf deny 10

    match ip address prefix-list rip_routes

    router rip

    redistribute ospf 10 route-map redis-ospf subnets

 

C.  ip prefix-list rip-to-ospf permit 10.1.1.8/25 ge 26 le 28 route-map redis-rip deny 20

    match ip address prefix-list rip-to-ospf

    router ospf 100

    redistribute rip route-map redis-rip subnets

 

D.  access-list 15 deny 10.1.1.0 0.0.0.63

    access-list 15 permit any

    route-map redis-rip deny 10

    match ip address 15

    route-map redis-rip permit 20

    router ospf 100

    redistribute rip route-map redis-rip subnets

 

Correct Answer: AD

 

 

QUESTION 157

What is the best order for choosing the Router-ID in ospf?

 

A.       high loopbak interface address,high physical interface address, Router ID command

B.       high loopbak interface address, Router ID command, high physical interface address

C.       Router ID command, high loopbak interface address, high physical interface address

D.      Router ID command, high physical interface address, high loopbak interface address

E.       high physical interface address, high loopbak interface address, Router ID command

F.        high physical interface address, Router ID command, high loopbak interface address

 

Correct Answer: C

 

 

QUESTION 158

Refer to the exhibit. Router RTR is attempting to establish BGP neighbor relationships with routers RT1 and RT3. On the basis of the information that is presented in the exhibit, which two statements are true? (Choose two)

 

clip_image006

clip_image007

 

A.       RTR has a BGP password set but neighbor 10.0.0.1 does not

B.       RTR has a BGP password set but neighbor 10.0.0.5 does not

C.       RTR has a BGP password set but neighbor 10.0.0.1 has an incorrect password set

D.      RTR has a BGP password set but neighbor 10.0.0.5 has an incorrect password set

E.       Neighbor 10.0.0.1 has a BGP password set but RTR does not

F.        Neighbor 10.0.0.5 has a BGP password set but RTR does not

 

Correct Answer: AD

 

 

QUESTION 159

Refer to the exhibit diagram and configuration. RTB is summarizing its networks from AS 64100 with the aggregate-address command. However, the show ip route command on RTA reveals the RTB individual networks as well as its summary route. Which option would ensure that only the summary route would appear in the routing table of RTA?

 

clip_image008

 

A.       Delete the four network statements and leave only the aggregate-address statement in the BGP configuration.

B.       Add the keyword summary-only to the aggregate-address command.

C.       Add a static route with a prefix of 192.168.24.0 255.255.252.0 pointing to the null0 interface.

D.       Create a route map permitting only the summary address.

 

Correct Answer: B

 

 

QUESTION 160

Refer to the exhibit. The neighbor 10.1.1.1 weight 200 BGP configuration command has been configured on router A. What will be the result of this configuration?

 

clip_image009

 

A.       Router A will prefer the path through router B for network 172.20.0.0.

B.       Router A will prefer the path through router C for network 172.20.0.0.

C.       Packets from router D will prefer the path through router B for networks advertised by router A.

D.      Packets from router D will prefer the path through router C for networks advertised by router A.

 

Correct Answer: A

 

Download Latest Complete Collection of CCNP 642-902 Real Exam ,help you to pass exam 100%.

Ensurepass Cisco Certifications Exam Questions and Answers
Ensurepass CCNP Exams Questions and Answers

Leave a Reply