New Updated Cisco ICND2 200-101 Real Exam Download 281-290

Ensurepass

QUESTION 281

clip_image002

 

Click the console of the HOME router. Input the following command into CLI on the right side

 

Home> enable

Home # show run

clip_image004

 

Home # show cdp neighbor

clip_image006

 

examine the configuration information’s related to problem solution.

Drag and drop question. Drag the items to the proper locations.

 

Correct Answers:

clip_image008

 

 

QUESTION 282

The left describes the types of cables, while the right describes the purposes of the cables. Drag the items on the left to the proper locations. (Not all items can be used.)

 

Select and Place:

clip_image010

 

Correct Answer:

clip_image012

 

 

QUESTION 283

clip_image014

 

Correct Answer:

clip_image016

 

 

QUESTION 284

The left provides some routing protocols, while the right gives several Cisco default administrator distances. Drag the items on the right to the proper locations.

clip_image017

 

Correct Answer:

clip_image018

 

 

QUESTION 285

Drag and drop. Match the items on the left with its corresponding definition on the right.

clip_image019

 

Correct Answer:

clip_image021

 

 

QUESTION 286

As a CCNA candidate, you need to know EIGRP very well. Which tables of EIGRP route information are held in RAM and maintained through the use of hello and update packets? Please choose two appropriate tables and drag the items to the proper locations.

 

Select and Place:

clip_image022

 

Correct Answer:

clip_image024

 

 

QUESTION 287

clip_image026

 

Correct Answer:

clip_image028

 

 

 

 

QUESTION 288

clip_image030

 

Correct Answer:

clip_image032

 

 

QUESTION 289

Drag and drop question. Drag the items to the proper locations.

clip_image034

Correct Answer:

clip_image036

 

 

QUESTION 290

VTP Configuration LAB

A new switch is being added to the River Campus LAN. You will work to complete this process by first configuring the building_210 switch with an IP address and default gateway. For the switch host address, you should use the last available IP address on the management subnet. In addition, the switch needs to be configured to be in the same VTP domain as the building_100 switch and also needs to be configured as a VTP client. Assume that the IP configuration and VTP configuration on building_100 are complete and correct.

 

The configuration of the router is not accessible for this exercise. You must accomplish the following tasks:

 

Determine and configure the IP host address of the new switch.

Determine and configure the default gateway of the new switch.

Determine and configure the correct VTP domain name for the new switch.

Configure the new switch as a VTP client.

 

clip_image038

 

Correct Answer:

Here are the Steps for this Lab Solution:

The question states we can’t access the router so we can only get required information from switch building_1. Click on the PC connected with switch building_1 (through a console line) to access switch building_1s CLI. On this switch use the show running-config command:

 

building_1#show running-config

 

Next use the show vtp status command to learn about the vtp domain on this switch

 

building_1#show vtp status

 

(Notice: the IP address, IP default-gateway and VTP domain name might be different!!!) You should write down these 3 parameters carefully.

 

Configuring the new switch

+ Determine and configure the IP host address of the new switch The question requires “for the switch host address, you should use the last available IP address on the management subnet”. The building_1 switch’s IP address, which is 192.168.22.50 255.255.255.224, belongs to the management subnet.

 

Increment: 32 (because 224 = 1110 0000)

Network address: 192.168.22.32

Broadcast address: 192.168.22.63

 

The last available IP address on the management subnet is 192.168.22.62 and it hasn’t been used (notice that the IP address of Fa0/1 interface of the router is also the default gateway address 192.168.22.35).

Also notice that the management IP address of a switch should be configured in Vlan1 interface. After it is configured, we can connect to it via telnet or SSH to manage it.

 

Switch2#configure terminal

Switch2(config)#interface Vlan1

Switch2(config-if)#ip address 192.168.22.62 255.255.255.224

Switch2(config-if)#no shutdown

 

+ Determine and configure the default gateway of the new switch The default gateway of this new switch is same as that of building_1 switch, which is 192.168.22.35

 

Switch2(config-if)#exit

Switch2(config)#ip default-gateway 192.168.22.35

 

+ Determine and configure the correct VTP domain name for the new switch The VTP domain name shown on building_1 switch is Cisco so we have to use it in the new switch (notice: the VTP domain name will be different in the exam and it is case sensitive so be careful)

 

Switch2(config)# vtp domain Cisco

 

+ Configure the new switch as a VTP client

 

Switch2(config)#vtp mode client

 

We should check the new configuration with the “show running-config” & “show vtp status”; also try pinging from the new switch to the the default gateway to make sure it works well.

Finally save the configuration

 

Switch2(config)#exit

Switch2#copy running-config startup-config

 

Download Latest Complete Collection of ICND2 200-101 Real Exam ,help you to pass exam 100%.

Ensurepass Cisco Certifications Exam Questions and Answers
Ensurepass CCNA Exams Questions and Answers

Leave a Reply